SATIS MACHINERY CO., LTD.

Products

Home > Products > Finned Tube Coil Fabrication Machinery > Hairpin Bender > China Hairpin Bender

China Hairpin Bender

Min. Order:
1 Bag/Bags
Share:
Chat Now
  • Product Description
Overview
Product Attributes

Model No.1250

                                   Satis Mechanical Hairpin Bender


SHP8-1500 Model Satis Mechanical hairpin bender quoted here consist of:

1. Powered uncoiler station

2. A changeable rerounding & straightening system to allow for further diameter changes.



The rounding & straightening wheels are set on both the vertical and horizontal plane, which will straight the tubes from the 2 plates. Each tube has 2 rounding wheels and 12 straighten wheels



The feeding system is a hydraulically driven friction feeding device, with air cylinders controlling the actual pressure applied to the individual feed belts. When feeding, individual air cylinders will apply proper pressure to each of the belts. The upper and bottom belts will clamp one copper tube and feed to proper length.when the proper length is almost achieved. The feeding speed will change from fast to slow, and the air cylinder pressure on the belt will change from high to low. Each air cylinder will lose almost all pressure when the tube it is feeding reaches the final proper position against a Hard Stop plate. It will hold that tube in place until all tubes have achieved the final proper position. Thus all hairpin ends are in the same final location assuring both the consistence of hairpin length and equality of leg lengths



3. A fixed location cutting system

The copper tubing cutting system utilizes outer rotating cutter blades to cut the tube. Lubrication takes place. The feed belts reverse and separate the tube ends after cutting.



4.A Satis Mechanical Hairpin Bending system

The bending system can move in the length direction to produce hairpin of different lengths. The leg length is set from the PLC and Programming is fully automatic



The bend system is servo driven. This is allows for much better accuracy and less free play or back lash then the older type of hydraulically driven bending heads found in many competitor's units.



5 In addition:

"Quick Change" Tube support booms are provided to support the guide tubes and allow change from one length to another in less than 2 minutes



The Hairpin bender will be capable of receiving such special sets of bend tooling as may be dictated by specific bend radius requirements and / or changes in tubing diameter up to 16mm maximum.



A sensing device is provided in each lubrication tank to monitor the level of oil to prevent operating the equipment without proper lubrication. A corresponding diagnostic message will be displayed on the touch screen when the level is low



An tube pick off device is included which will support the tubes while stripping and lay them down in the tube collectors. This will produce straighter hairpins for longer lengths

There is a tube end Sizer attachment to reopen the ends of the hairpins that do not pass

over the mandrels



Automatic setup of the hairpin bender and leg length adjustments can be accomplished through the use of a standard programmable controller interfaced with a touch screen. This also provides diagnostic information for trouble shooting, Semi-automatic control and manual actuation of all machine functions. 

Additionally, The machine is capable of automatically positioning to specific hairpin 

length. Both legs of hairpin are adjustable through the touch screen and can be moved 

either independently or together by dedicated servo motors. The motors are capable of 

running at both fast and slow speeds to decrease setup time and facilitate precision 

adjustments. Over-travel switches on each axis help protect the machine with digital

readouts on the touch screen display the current and target location in increments of 

0.1mm. After the target location on each axis has been reached, hydraulic clamps lock in 

place to prohibit drifting.



Cable/hose carriers are provided to the back of the machine and the switch tower area to prevent hose and cable damage and imprve the general esthetic of the equipment.



Industry standard assemblies are also supplied-such as

1. Stripper tube protectors

2. Cable & Hose carriers

3. Quick disconnects

4. Oil level sensors






Product Categories : Finned Tube Coil Fabrication Machinery > Hairpin Bender

Email to this supplier
  • *Subject:
  • *To:
    Mr. David Xu
  • *Email:
  • *Message:
    Your message must be between 20-8000 characters

Home > Products > Finned Tube Coil Fabrication Machinery > Hairpin Bender > China Hairpin Bender

Send Inquiry
*
*

Send Inquiry

Tel:86-574-83023019

Fax:86-574-87489428

Mobile Phone:+8613615883733Contact me with Whatsapp

Email:info@satismachinery.com

Address:2# Xinheng Yizhilu, Cicheng Industry Park, Jiangbei Dist. 315036 , Ningbo, Zhejiang

Mobile Site

Home

Product

Whatsapp

About Us

Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send